periop.blogg.se

1. #Motorola programming cable gm300 25 pin to rj45 how to#
2. #Motorola programming cable gm300 25 pin to rj45 software#

Please contact us if you need another type of connector installed. more this kit in chrome and have different connector options available if needed. Item New Tram 3 1/2 black zinc Magnet mount antenna base with mini UHF connector and 17 ft of coax cable which fits for Motorola mobiles. Visit us today! at 2WayRadioParts com.RcmdId ViewItemDescV4,RlogId p4%60bo7%60jtb9%3Feog4d71f%2B0a7%3E-14b4f3bcbb9-0x108. MOTOTRBO™ DGM™ 4100+, MOTOTRBO™ DGM™ 6100, MOTOTRBO™ DGM™ 6100+, MOTOTRBO™XPR™4300, MOTOTRBO™XPR™4350, MOTOTRBO™XPR™4380, MOTOTRBO™XPR™4500, MOTOTRBO™XPR™4550, MOTOTRBO™XPR™4580 We carry a complete line of Motorola original parts and accessories for all Motorola models. Compatible with the following models: ALL Maxtrac Mobiles. more or less or use while on low power mode. New Genuine OEM Motorola Part HKN9407A Fused Power Cord Adapter Motorola OEM Mobile Power Cord Assembly For use with mobile radios operating at 25 watts. So if you make your own cable make sure to use the Motorola pin numbering convention.New Genuine OEM Motorola Part HKN9407A Fused Power Cord Adapter Motorola OEM Mobile Power Cord Assembly For use with mobile radios operating at 25 watts.

#Motorola programming cable gm300 25 pin to rj45 software#

With the power applied to the red & black pigtail the Radio Doctor software worked just fine.īe aware that the Motorola pin numbering convention on the RJ45 connector is the reverse sequence from the standard pin numbering convention. Once I applied power to the pigtail the Radio Doctor software worked as it should and I was able to retrieve the radio's configuration and figure out which repeaters were still current and which ones were not. I bit of digging and I found on this web site an answer these "3 in 1 programming cable" units require a nominal 9 volts DC to the red and black pigtail. They did not in anyway answer my question. They replied with a semi-coherent reply which essentially told me that it was radio and the PC.

#Motorola programming cable gm300 25 pin to rj45 how to#

I contacted the seller with specific questions about how to connect the interface and whether the red and black wire-pigtail on the adapter also required power and if so how much power. The Interface came with no documentation at all. The "3 IN 1 Programming Cable" shipped from China and arrived within a few days of the estimate in the eBay listing. I also ordered from eBay a "3 IN 1 Programming Cable" which is an RPC-M300 or a clone of that unit (see photos below to find a similar unit) which had the RJ-45 Crystal plug or whatever Motorola calls their RJ45 connector on the GM300 radio.

I joined the Radio Doctor Yahoo Group and downloaded the Radio Doctor software from the files section of the Yahoo Group. However this did not give me any information on what if any CTCSS tone programming had been done on thoe frequencies. I used a frequency counter and guessed based upon the standard repeater offset what the receive frequencies were. I only knew that it was programmed for the HAM bands. I started out with a GM300 radio, it came to me with no documetation about the radio and how to use it and no documentation on how it was currently programmed.

I ordered the interface off of eBay and it came with no documentation and I would later learn that the interface requires a 9 volt input to work. I was inspired to create this page because I got a programming interface for a GM300 which came with no documentation. Tip on using the RPC-M300 "3 in 1" programming cable: Motorola GM300 Programming - FJ45.COM FJ45.COM